DataCard LM200 Guide de l'utilisateur Page 47
- Page / 109
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
SR200 & SR300 Printer and LM200 & LM300 Laminator User Guide 41
6 Click the Update button to activate the security lock and prevent access to the
supplies in the printer.
Tips for Success
• Write down the password and store it in a safe place.
• Do not forget the password. You can ask your service provider for assistance, but
this is not covered by the warranty.
•
The Status Monitor password and the security number entered on the printer panel are
not linked.
You can use different values for these items.
Status monitor messages
The following messages are displayed in message boxes by the Status Monitor. See
“Printer Status tab” on page 33.
Error Code Displayed Message Solution
0102D000 Cards have run out.
Load cards as described in
“Load cards” on
page 8
.
0102D000 The card hopper is detached. Close or replace the card hopper securely.
0102D100 Printer door is open. 1 Close the printer door.
2 Press Reset and then Enter to initialize the
printer.
0102D100 The cleaning unit is detached. 1 Install the Cleaning Unit and then close the
door. See “Cleaning the cleaning unit” on
page 62
,
2 Press Reset and then Enter to initialize the
printer.
0102D300
0102D400
0102D500
The printer is busy. —
0102DA00 Preheating is in progress. Wait until preheating is complete.
0102DB00 Printer is initializing. Wait until initialization is complete.
0102DC00 Offline testing is in progress. Wait until the offline test is complete.
Cleaning is in progress. Wait until cleaning is complete.
0102DD00 Operator panel is currently in use.
—
The printer is in the transport mode. Cancel the transport mode.
0102DE00 The firmware cannot be downloaded. Set the printer to the download mode.
- User Guide 1
- Trademark acknowledgments 2
- Proprietary Notice 2
- Contents 3
- 5 Messages 5
- Liability statement 6
- Introduction 7
- About the printer 8
- The inside of the printer 9
- The back of the printer 10
- About the laminator 11
- Using the printer 13
- Load Supplies 14
- Remove Hopper and Cards 15
- Replace the Hopper 15
- Adjust Card Thickness 15
- Load ink ribbon 16
- Load retransfer film 17
- Load top side laminate film 18
- Take-up Spool 19
- Supply Roll 19
- Guide Shaft 19
- Metal Guides 19
- Power on 20
- Optional laminator connection 21
- Power on the laminator 21
- Power on the printer 22
- Prepare to print cards 23
- Printing cards 23
- Print cards using ID software 24
- Print from a PC application 24
- Tips for Success 25
- Viewing and changing 27
- Printing Preferences 28
- Print tab 29
- Priority of Data 31
- 1 Panel Auto 2 Panels 31
- Page Split 32
- Security Erase 33
- Printing Area Settings 34
- Printer Settings 34
- Encode tab 35
- Laminate tab 35
- Configuration tab 35
- Printing Properties 36
- Status Monitor 37
- Close the Status Monitor 38
- Printer Status tab 39
- Printer Setting tab 40
- Retransfer tab 41
- Bend Remedy tab 42
- Media Setting tab 42
- Property tab 43
- Laminator tab 44
- Printer Select tab 45
- Others tab 46
- Security Lock tab 46
- Status monitor messages 47
- “Mending 49
- Using the LCD Menus 55
- Using the Printer LCD Panel 57
- Printer Security Number 63
- Red Status Light 64
- Blue Status Light 64
- Operator Button 64
- “Laminator 65
- LCD messages” on page 84 65
- Laminator Settings 66
- Taking care of your printer 67
- Cleaning the printer 68
- Tips – Cleaning card feed 69
- Cleaning the magnetic head 70
- Cleaning the thermal head 71
- Cleaning printer fan filters 71
- Cleaning the laminator 73
- Laminator fan filter 75
- Messages 77
- Printer error recovery 78
- Transfer jam 79
- Turnover jam 80
- Retransfer section jam 81
- Printer LCD messages 83
- “Operating environment” on 85
- “Load cards” on 85
- Take -up side 86
- Laminate pressure motor 86
- Supply side 86
- Supp ly Roll 87
- Patch Position 88
- Card warping 89
- Laminator LCD messages 90
- Supplies 93
- Ink ribbon 94
- Retransfer film 94
- Laminator material 95
- Cleaning supplies 96
- Site requirements 97
- Site guidelines 98
- Ventilation clearance 99
- Printer specifications 100
- Laminator specifications 101
- Magnetic Stripe Encoding 103
- Inline Encoding 104
- Character Code Table 105
- Compliance (FCC) 107
- Regulatory compliance 108
- 11111 Bren Road West 109
- Minnetonka, MN 55343-9015 109
- 952.933.1223 109
- 952.933.7971 FAX 109
© 2020, manymanuals.fr. Tous droits réservés | 0.765 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels