DataCard LM200 Guide de l'utilisateur Page 52
- Page / 109
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
46 SR200 & SR300 Printer and LM200 & LM300 Laminator User Guide
05000060 Thermostat is broken. • Turn off the power and turn it on again. If the
same problem occurs, consult an authorized
dealer or service personnel.
05000061 The temperature of the top side Heat
Roller is too high.
05000062 The temperature of the bottom side Heat
Roller is too high.
05000063 The internal temperature of the top side
Heater is too high.
05000064 The internal temperature of the bottom
side Heater is too high.
05000065 A hardware error has occurred in the top
side Heat Roller.
05000066 A hardware error has occurred in the
bottom side Heat Roller.
05000067 The thermistor of the top side Heat
Roller is faulty.
05000068 The thermistor of the bottom side Heat
Roller is faulty.
0500006B A cam error has occurred in the top side
Heat Roller.
0500006C A cam error has occurred in the bottom
side Heat Roller.
0500006D The operating ambient temperature of
the laminator is too low.
• User the laminator within the prescribed range.
When starting up the laminator in a low
temperature environment, the temperature of
the interior may remain low even though the
surrounding temperature has gone up. Turn on
the power again after waiting about one hour.
0500006E A hardware error has occurred in the top
side Film Supply Encoder.
• Turn off the power and turn it on again. If the
same problem occurs, consult an authorized
dealer or service personnel.
0500006F A hardware error has occurred in the
bottom side Film Supply Encoder.
05000070 A hardware error has occurred in the top
side Film Take-up Encoder.
05000071 A hardware error has occurred in the
bottom side Film Take-up Encoder.
0500007D Other error is detected.
Error Code Displayed Message Solution
- User Guide 1
- Trademark acknowledgments 2
- Proprietary Notice 2
- Contents 3
- 5 Messages 5
- Liability statement 6
- Introduction 7
- About the printer 8
- The inside of the printer 9
- The back of the printer 10
- About the laminator 11
- Using the printer 13
- Load Supplies 14
- Remove Hopper and Cards 15
- Replace the Hopper 15
- Adjust Card Thickness 15
- Load ink ribbon 16
- Load retransfer film 17
- Load top side laminate film 18
- Take-up Spool 19
- Supply Roll 19
- Guide Shaft 19
- Metal Guides 19
- Power on 20
- Optional laminator connection 21
- Power on the laminator 21
- Power on the printer 22
- Prepare to print cards 23
- Printing cards 23
- Print cards using ID software 24
- Print from a PC application 24
- Tips for Success 25
- Viewing and changing 27
- Printing Preferences 28
- Print tab 29
- Priority of Data 31
- 1 Panel Auto 2 Panels 31
- Page Split 32
- Security Erase 33
- Printing Area Settings 34
- Printer Settings 34
- Encode tab 35
- Laminate tab 35
- Configuration tab 35
- Printing Properties 36
- Status Monitor 37
- Close the Status Monitor 38
- Printer Status tab 39
- Printer Setting tab 40
- Retransfer tab 41
- Bend Remedy tab 42
- Media Setting tab 42
- Property tab 43
- Laminator tab 44
- Printer Select tab 45
- Others tab 46
- Security Lock tab 46
- Status monitor messages 47
- “Mending 49
- Using the LCD Menus 55
- Using the Printer LCD Panel 57
- Printer Security Number 63
- Red Status Light 64
- Blue Status Light 64
- Operator Button 64
- “Laminator 65
- LCD messages” on page 84 65
- Laminator Settings 66
- Taking care of your printer 67
- Cleaning the printer 68
- Tips – Cleaning card feed 69
- Cleaning the magnetic head 70
- Cleaning the thermal head 71
- Cleaning printer fan filters 71
- Cleaning the laminator 73
- Laminator fan filter 75
- Messages 77
- Printer error recovery 78
- Transfer jam 79
- Turnover jam 80
- Retransfer section jam 81
- Printer LCD messages 83
- “Operating environment” on 85
- “Load cards” on 85
- Take -up side 86
- Laminate pressure motor 86
- Supply side 86
- Supp ly Roll 87
- Patch Position 88
- Card warping 89
- Laminator LCD messages 90
- Supplies 93
- Ink ribbon 94
- Retransfer film 94
- Laminator material 95
- Cleaning supplies 96
- Site requirements 97
- Site guidelines 98
- Ventilation clearance 99
- Printer specifications 100
- Laminator specifications 101
- Magnetic Stripe Encoding 103
- Inline Encoding 104
- Character Code Table 105
- Compliance (FCC) 107
- Regulatory compliance 108
- 11111 Bren Road West 109
- Minnetonka, MN 55343-9015 109
- 952.933.1223 109
- 952.933.7971 FAX 109
© 2020, manymanuals.fr. Tous droits réservés | 0.122 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels